Voltage stabilizer Togo: 220 V port and cold chain

How to size a voltage stabilizer for Togo's 220/380 V CEET supply: sag in the port zone, servo versus static, kVA maths and Lomé import documents.

Togo’s supply is 220 V single-phase and 380 V three-phase at 50 Hz, a legacy IEC value that sits one step below the 230/400 V used across most of Europe. For a port economy built on transit cargo, clinker grinding and phosphate processing, that single step decides how imported equipment behaves at the end of a long feeder. A voltage stabilizer Togo’s operators install is therefore chosen against measured sag at the point of use, not against the nameplate on the machine.

Togo’s grid: 220/380 V, 50 Hz, CEET and ARSE

The Compagnie Energie Electrique du Togo (CEET) supplies the national grid. Distribution voltage is 220 V single-phase and 380 V three-phase at 50 Hz, so three-phase motors and drives built for 400 V operate marginally below their design flux and draw correspondingly more current for the same shaft power. Regulation of the sector sits with the Autorite de Reglementation du Secteur de l’Electricite (ARSE), while product standards fall under the national framework administered by the Ministry of Trade.

Two consequences follow for anyone specifying equipment:

  • 220 V nominal is 4% below 230 V. Resistive loads such as heaters and ovens deliver less output, and motors run at higher current for the same mechanical work — a detail that matters when a machine’s full-load current is already close to its protection setting.
  • Sag, not overvoltage, is the usual problem. Long low-voltage feeders feeding industrial plots and the port zone pull the voltage down at peak hours. A site that measures 218 V at midnight may see 195 V at the afternoon peak, which is where contactors chatter and VFDs trip.

Overvoltage does occur, but it is usually a transient tied to switching and load rejection rather than a sustained condition. That asymmetry should drive the specification: a voltage stabilizer sized for Togo needs a deep input window on the low side and surge protection on the high side.

Where a voltage stabilizer Togo’s industry clusters need one

Four load patterns dominate, and the voltage stabilizer Togo’s operators buy differs by cluster. Port logistics is the first: ship-to-shore and yard equipment, reefer plugs for cold containers and the cold stores behind them. Phosphate processing is the second, with continuous heavy loads where a trip means a restart sequence measured in hours. Cement grinding in the port zone is the third, dominated by large mill motors and high starting currents. Food and beverage processing is the fourth, where refrigeration sits alongside PLCs, weigh cells and filling heads that tolerate very little voltage error.

Servo or static: which fits a Togolese site

Where the logged input drops below 200 V, or where the load is motor-dominated, the servo voltage stabilizer is the correct choice. Mertios servo units correct an input window from 112.6 V to 537 V to ±0.4% output accuracy, so the same unit handles the afternoon sag and the switching transient that follows a feeder reclose.

Criterion Servo stabilizer Static regulator
Input window Wide and continuous Narrower, tap-stepped
Response Mechanical, settles in tens of ms Fast, sub-cycle
Deep sag behaviour Holds the load online May transfer to bypass or trip
Motor starting Tolerates inrush with headroom Current-limited, needs oversizing
Maintenance Brush and track wear No moving parts
Typical Togo fit Mills, cold stores, phosphate plant Control rooms, IT, small labs

For a reefer yard or a mill incomer, static regulation looks attractive on paper because it has no brushes. In practice the events that damage cargo and stop production are the deep, sustained sags that a tap-stepped unit cannot correct without dropping to bypass — which is precisely when protection is needed.

Sizing a voltage stabilizer Togo’s cold chain can defend: a worked example

Suppose a cold store near the port runs 24 reefer plugs at 5.5 kW each, plus 60 kW of compressors and 15 kW of lighting and offices, on a 380 V three-phase supply.

  1. Sum the connected load: 24 × 5.5 = 132 kW of reefer load, plus 60 kW of compressors and 15 kW of ancillary load, giving 207 kW.
  2. Convert to current at 380 V with a combined power factor of 0.85: I = 207,000 / (1.732 × 380 × 0.85) ≈ 370 A.
  3. Add margin for simultaneous compressor starting: 25% headroom brings the design current to ≈ 462 A.
  4. Convert back to apparent power: 462 A at 380 V is ≈ 304 kVA, so specify a 320 kVA unit.
  5. Check the low-side window: if commissioning logs show 190 V at peak, the voltage stabilizer must correct from that point without bypassing — confirm the rating holds at reduced input voltage, not only at nominal.
  6. Confirm the bypass and the downstream protection are rated for the same current, and that the neutral is sized for the harmonic content of the reefer rectifiers.

Reefers are rectifier loads, so harmonic distortion on the neutral is a real design constraint in a container yard. A stabilizer with an isolating transformer in front of the regulator handles that far better than one wired straight into the busbar.

Standards, conformity and import documentation

Togo does not have a single widely recognised national mark equivalent to SNI in Indonesia or NOM in Mexico; product standards sit within the national framework administered by the Ministry of Trade, and importers are routinely asked for a certificate of conformity alongside commercial documents. Every voltage stabilizer Togo’s importers clear should therefore arrive with the manufacturer’s IEC test reports attached, and treat those as the practical reference: IEC 60038 for the voltage basis, IEC 61558 for the transformer, and IEC 61000 for immunity and harmonic emissions.

In the purchase order, name the tests rather than the standard numbers alone: type test at the ordered kVA, temperature rise at full load, efficiency at 50% and 100% load, and the actual measured input window. A conformity certificate that does not state the tested rating cannot be used to defend the equipment at clearance.

Lomé, the corridor and getting a cabinet to site

Lomé is a deep-water port and a regional transshipment hub, and the same corridor that carries transit cargo to landlocked neighbours carries imported machinery inland. A voltage stabilizer above roughly 100 kVA ships as a floor-standing cabinet, so plan for the last kilometre rather than the sea leg: crane access at the port, a truck with a tail-lift or a proper ramp, and a door wide enough for the cabinet.

Salt air is the other logistics issue. Coastal installations in the port zone corrode faster than inland sites, so specify painted enclosures with a corrosion class suited to the environment, and inspect terminals at commissioning rather than after the first rainy season.

Voltage stabilizer Togo: frequently asked questions

Is 220 V equipment from Europe usable in Togo?

Yes. Equipment rated 220–240 V operates normally, and most modern switch-mode supplies accept the range. Fixed-speed motors and heaters are the exceptions: at 220 V they draw more current or deliver less output, so check full-load current against protection settings.

Can a stabilizer replace the generator at a Togo site?

Not on its own. A voltage stabilizer Togo’s port-zone sites install usually sits downstream of the changeover, so it protects the load from both grid and generator supply while the generator carries the outage itself.

Where should the unit be installed relative to the distribution board?

As close to the sensitive load as practical, with a maintenance bypass. Long cable runs after the stabilizer reintroduce voltage drop, which defeats the ±0.4% accuracy the unit was bought for.

How much headroom is needed for motor starting?

Enough to cover the largest motor starting while other loads run. Direct-on-line starts need the most; soft starters and VFDs reduce the requirement, but they inject harmonics that the voltage stabilizer must tolerate.

Planning a comparable installation? These guides cover the matching grid conditions, sizing method and import requirements:

All Mertios guides

Leave a Reply

Your email address will not be published. Required fields are marked *

Chat on WhatsApp+90 544 243 21 66